RV-7/A 320 150/160
We offer three standard options for flight performance: climb, a “good all-around” performer and a cruise prop.
The climb propeller will have a lower pitch; this increases the static RPM during takeoff. This is a great option if Density Altitude needs to be a considering factor for your home airport operations or mountain flying. It is important to note that the climb propeller will slightly exceed 2700 RPM at wide open throttle.
The “good all around” performing propeller is right in between climb and cruise performance and is our standard recommendation, especially for your first flight. This prop will hit 2700 RPM at 7500’ DA in straight and level flight.
The cruise propeller has the same top speed as other recommended propellers listed just at a lower RPM, great for fuel economy. With this cruise propeller you would expect to see 2650 RPM at wide open throttle at 7500’ DA. The static RPM is lower with this prop so it will take longer to accelerate but will let you reach your airframe’s top speed in cruise. This prop is great if you’re flying off longer runways or plan on doing a lot of cross countries.
It’s important to note that all of our props are capable of achieving the same top speed, it’ll just be at a different RPM.
Additionally, any engine modifications such as changes to the: compression ratio, electronic ignition, port & polish, etc. all add to your available horsepower and will be factored into your propeller selection.
Difference between the two and three bladed propellers:
A three bladed is much quieter and smoother, you’re able to run a smaller diameter so greater ground clearance and it has more of a braking affect when you pull the power back. You will also see your RPM will come up faster as you start accelerating on takeoff. The two bladed is slightly faster at wide open throttle around 2-3 mph top speed below 7500’ but the three bladed will maintain its speed at 12,500’ but the two bladed loses top speed. The three bladed becomes a few mph faster at 12,500’. The climb performance between the two are very similar.
The following table represents our standard recommendations available but may vary slightly depending on the speed and specifications of your current airframe
|320/150hp||2-Bladed Diameter||3-Bladed Diameter||Pitch||Design RPM @ 7500’||WOT at 7500’ DA||WOT at Sea Level|
|“Good All Around”||68”||66”||71”||2700||187-189mph||197-199 mph|
|320/160hp||2-Bladed Diameter||3-Bladed Diameter||Pitch||Design RPM @ 7500’||WOT at 7500’ DA||WOT at Sea Level|
|“Good All Around”||68”||66”||72”||2700||190-192mph||200-202 mph|
Speeds are based off the average we see.
We do manufacture propellers for the RV-7/A with different power plants, just drop us an email at: email@example.com
Leading Edge Protection Options
Nickel: Nickel is an additional leading edge protection which is great if you fly through rain, off grass or off strips that aren’t that well maintained. It is very durable and allows you to fly through rain at any RPM without erosion. If you are a fair-weather flyer the nickel isn’t necessary for your flight operations.
LET tape: We offer a polyurethane leading edge tape to protect the leading edge of erosion through rain. You can still get some nicks from small debris and rocks. The adhesive on the tape normally starts breaking down after 3-5 years and will need to be replaced. We do sell kits so you can install or replace it yourself.
Without nickel or leading edge tape the propeller will hold up like a wooden propeller through rain. You’re able to fly through rain without leading edge protection if you are throttled back below 2200 RPM. With the leading edge tape or nickel you’re able to fly through rain at your cruise throttle without erosion.
Hardware needed for the RV-7/A:
The RV-7/A can use a 2.25” if you have a stock cowling or a 4” extension if you have an aftermarket cowling. We require a 7” diameter mounting surface and all six lugs to protrude into the propeller at least .350”. If you have a smaller diameter mounting surface or if you do not have extended length lugs you will need a new extension. There have been many evolutions of extensions throughout the years. If your extension has both the extended length lugs and a 7” diameter mounting surface we will try to accommodate and get you all the parts you may need for install.
If you are purchasing a new extension we will need to know if you have 3/8” or 7/16” bolts.
If you are going to reuse your existing extension we will need to know the bolt size on the prop size of the extension. Additionally, let us know if you have a lock nut on the back of the propeller bolt or if the extension has a threaded lug.
Bolts: We can supply the engine and propeller bolts for you. We aren’t able to get bolts longer than 7”.
Crush Plate: We do require a 7” diameter crush plate to be mounted on the face of the propeller. We have them available in a variety of thicknesses depending on the installation. If you’re using Van’s spinner kit, the alignment between the front and rear bulkhead is critical. Just let us know and we can ensure you get the correct thickness crush plate for everything to align properly. We also offer a weighted crush plate if you need to move your CG forward.
Spinner for the RV-7/A:
The RV-7/A uses a 13” spinner. We sell a carbon fiber spinner dome, a fixed self-centering carbon front bulkhead and an aluminum rear bulkhead. If you anticipate using a weighted crush plate, please let us know as we have a different forward bulkhead in order to accommodate the weighted crush plate.
Two bladed propeller: $2450
Shipping Two Bladed Propeller within US, excluding Hawaii and Alaska: $135
Three bladed propeller: $2950
Shipping 3-Bladed within the US, excluding Hawaii and Alaska: $285 to a commercial address or $325 to a residential address
Nickel: $250 per blade
Leading Edge Tape, per blade installed: $35
2.25” extension with a crush plate, engine bolts and prop bolts:
4” extension with a crush plate, engine bolts and prop bolts: $710
13” Spinner: $575